Design and analysis of a truss deployable antenna mechanism based on a 3UU-3URU unit

Space deployable structures with large calibers, high accuracy, and large folding ratios are indispensable equipment in the aerospace field. Given that the single-DOF 3RR-3RRR deployable unit cannot be fully folded, this study proposes a 3UU-3URU deployable unit with two kinds of DOF: folding movement and orientation adjustment. First, based on the G-K formula, the DOF of the 3UU-3URU unit is analyzed. Then, the 3UU-3URU unit is used to construct a deployable truss antenna with a curved surface, and the DOF of the whole deployable antenna containing multiple 3UU-3URU units is calculated. The structural design of a deployable antenna with two loops is carried out with specific parameters and geometric relations. Next, a DOF simulation of a basic combination unit composed of three 3UU-3URU units is performed. Finally, a prototype of the basic combination unit is manufactured, and the DOF of the mechanism is experimentally verified.     

Stall flutter prediction based on multi-layer GRU neural network

The modeling of dynamic stall aerodynamics is essential to stall flutter, due to the flow separation in a large-amplitude pitching oscillation process. A newly neural network based Reduced Order Model (ROM) framework for predicting the aerodynamic forces of an airfoil undergoing large-amplitude pitching oscillation at various velocities is presented in this work. First, the dynamic stall aerodynamics is calculated by solving RANS equations and the transitional SST-γ model. Afterwards, the stall flutter bifurcation behavior is calculated by the above CFD solver coupled with structural dynamic equation. The critical flutter speed and limit-cycle oscillation amplitudes are consistent with those obtained by experiments. A newly multi-layer Gated Recurrent Unit (GRU) neural network based ROM is constructed to accelerate the calculation of aerodynamic forces. The training and validation process are carried out upon the unsteady aerodynamic data obtained by the proposed CFD method. The well-trained ROM is then coupled with the structure equation at a specific velocity, the Limit-Cycle Oscillation (LCO) of stall flutter under this flow condition is predicted precisely and more quickly. In order to predict both the critical flutter velocity and LCO amplitudes after bifurcation at different velocities, a new ROM with GRU neural network considering the variation of flow velocities is developed. The stall flutter results predicted by ROM agree well with the CFD ones at different velocities. Finally, a brief sensitivity analysis of two structural parameters of ROM is carried out. It infers the potential of the presented modeling method to depict the nonlinearity of dynamic stall and stall flutter phenomenon.     

惯性参数对飞翼体自由度颤振特性的影响规律研究

飞翼飞行器刚体短周期模态频率较高,易与一阶弹性弯曲模态耦合发生一种特殊的颤振——体自由度颤振。采用风洞实验与频域计算相结合的手段,开展了惯性参数(俯仰转动惯量、质心位置)对飞翼飞行器体自由度颤振特性(颤振速度和颤振频率)的影响规律研究。实验和计算结果表明:俯仰惯量和质心位置会明显改变体自由度颤振频率与速度,颤振实验与计算结果一致性较好。俯仰惯量增加,颤振频率降低,沉浮约束时颤振速度基本不变,沉浮自由时颤振速度增大;质心位置前移,俯仰模态频率与阻尼同时增加,俯仰与一阶弹性弯曲模态耦合更容易,但发散模态分支的阻尼也更大,导致颤振速度先降低后增大,颤振频率单调增加。     

流量调节器管路系统自激振荡特性研究

流量调节器管路系统在小流量大压降工况下会出现低频自激振荡现象。为了深入认识自激振荡产生机理,结合某稳流型流量调节器及管路系统,基于流量调节器弹簧振子动力学模型开展数值仿真研究。数值仿真得出自激振荡频率为94Hz,与发动机试验结果一致。分析了流量调节器结构参数对系统稳定性的影响作用,三角形滑阀节流口能够抑制管路系统自激振荡。自激振荡产生机理是液动力随滑阀节流口型面振荡,并对管路系统形成正反馈作用,当流量调节器综合刚度系数<0时,管路系统就失稳产生振荡。某流量调节器的负载特性试验表明,随着流量调节器压降升高,管路系统稳定性变差。仿真获得的幅频特性,稳定边界与试验结果一致。     

流量调节器管路系统自激振荡特性研究（液体火箭推进专刊）

流量调节器管路系统在小流量大压降工况下会出现低频自激振荡现象,为了深入认识自激振荡产生机理,结合某型自稳流型流量调节器及管路系统,基于流量调节器弹簧振子动力学模型开展数值仿真研究。数值仿真得出自激振荡频率为94 Hz,与发动机试验结果一致。自激振荡产生机理是流量调节器的液动力受滑阀窗口型面变化率影响对系统形成正反馈作用,流量调节器综合刚度小于零时系统失稳。分析了流量调节器结构参数对系统稳定性的影响作用,三角形滑阀节流口流通面积能够抑制管路系统自激振荡。结合某型流量调节器负载特性试验系统进行验证,得出随着流量调节器压降升高,管路系统稳定性变差,获得的幅频特性,稳定边界与试验结果一致。     

压力振荡对气液同轴离心式喷嘴自激振荡的影响

为了研究供应系统振荡对气液同轴离心式喷嘴自激振荡的影响,采用水和空气作为模拟介质,开展了室压条件下冷态喷雾试验。通过试验分析了供应系统有/无振荡两种情况下离心式喷嘴的喷雾形态,以及供应系统有/无振荡两种情况下气液同轴离心式喷嘴自激振荡的喷雾形态。发现当离心式喷嘴供应系统振荡时,离心式喷嘴产生的锥形液膜也周期性地振荡,同时出现Klystron效应。液膜周期性振荡以及Klystron效应出现的频率与供应系统振荡频率一致。Klystron效应的出现使得喷雾锥角突然减小,锥形液膜发生折叠。供应系统振荡对自激振荡喷雾形态也有显著影响。供应系统振荡引起的Klystron效应使得液膜锥角减小,从而造成"圣诞树"型自激振荡喷雾上的"树枝"增多,同时自激振荡频率增加。这是因为当速度大的液膜追上速度小的液膜时,就会产生Klystron效应并使液膜速度增加。而液膜运动速度越大自激振荡频率也就越大。虽然在供应系统中施加激励没有发生"锁频"现象,但是自激振荡的强度在一定程度上减弱,并且伴随着自激振荡的"分频"现象,即自激振荡频率从一个主频向两侧分化为两个主频。     

基于正激波位置计算的进气道/发动机系统实时仿真模型

研究了超声速条件下,基于进气道内正激波位置计算的进气道/发动机系统综合仿真问题。提出了将超声速进气道分为内、外两部分独立计算的方案,外部通过斜激波计算公式获得进气道内部的边界条件,对进气道内部采用准一维CFD模型模拟背压对正激波位置的影响。相比二维CFD计算,在保证参数精度要求的前提下有效缩短了计算时间,提高了仿真实时性。进一步将进气道模型与发动机部件级模型匹配运行,构建了进气道与发动机综合实时仿真模型。进气道/发动机综合模型的仿真表明,其能够准确模拟进气道正激波位置对涡扇发动机的动稳态影响,当来流发生扰动时,通过喷管喉道面积和压缩部件导叶角的快速调节,能够抑制正激波位置的变化,并使推力下降量减少50%。      

双脉冲固体火箭发动机压强振荡特性研究

为了研究隔舱消融对双脉冲发动机中燃烧室的压强振荡影响规律,选择隔舱消融几个典型时刻进行研究,运用大涡模拟(LES)方法,对Ⅱ脉冲工作时的发动机流场稳定性进行数值模拟.最后得到了各工况下的压强时间曲线及其快速傅氏变换(FFT)结果.分析表明:由于Ⅱ脉冲工作初期隔舱暴露在流场中产生额外扰动,以及隔舱级间通道形成狭窄通道的加速作用,是导致边界层分离而引起障碍涡脱落的主要因素.点火初期,双脉冲发动机易发生轻微压强振荡.随隔舱消融,整个流场在发动机工作中、后期逐渐趋于平稳.      

伺服机构负载模拟系统设计与动态特性分析

针对火箭发动机喷管伺服机构的负载模拟问题,采用机械的方式,设计了一种可对伺服机构的惯性负载、摩擦力矩负载、弹性力矩负载、安装刚度以及发动机喷管柔性特征进行模拟的负载模拟器,并建立了模拟器和伺服机构数学模型。仿真分析了惯性负载、弹性力矩以及喷管柔性对伺服机构负载多自由度特性的影响。通过对伺服机构扫频实验,负载模拟器中的负载在一定范围内调节,可复现伺服机构实际工作中的动态特性。说明该负载模拟器结构设计合理,从而为具有多自由度特性的火箭伺服机构的负载模拟系统设计提供参考。该系统已经得到实际应用。     

OSCILLATION PHENOMENA IN FAR FIELD REGION OF PLANE JETS AT LOW REYNOLDS NUMBERS

Oscillation phenomena in far field region of plane jets are studied by lattice Boltzmann method over a range of Reynolds numbers （Re） from 16 to 65. Numerical results show that the instantaneous centerline velocities show periodic oscillation behavior in far field region when Re〉38. In contrast, the periodic behavior is invisible in corresponding flow field when Re≤38. For the cases of Re≤38, the exchange of momentum due to straining mo- tion gradually dominates the downstream flow filed, which qualitatively suggests the possibility of iet instability.